Halloween Wheel Window Card
This super-cute Halloween Wheel Window Card has a window and a wheel with spinning words. It's cute on its own or as a cover or insert for a junk journal!
To make it you'll need a few supplies:
Supplies:
Black Cardstock
Tim Holtz Ornate Plate
Brass Fastener
Circle Punch
Awl Or Other Sharp Tool
Craft Knife
Mounting Tape
Tape, Glue, Scissors, Etc.
Printables:
Pumpkin Image (I got mine from
Jento Design on Etsy)
(Pumpkin image is also available in the cover of my
Cozy Autumn Journal Kit Printable)
"Seasons" Journal Words Printable from My Porch Prints
Coffee Stained Book Pages Printable from My Porch Prints
Preparing The Black Card
To begin, cut an 8.5x11 inch sheet of black cardstock in half to create two 8.5x5.5 pieces. Then cut an
extra half-inch off the side & bottom of one piece. This will be your main card.
Punch Half-Circle
Punch a half-circle in the center bottom of the smaller, main card.
Bookplate Pumpkin
Next, place your book plate in the center of your pumpkin image and trace the inside, the outside corners, and the fastening holes.
Use your awl or sharp tool to punch the fastener holes.
Using a craft knife, cut out the center tracing.
Next, attach your bookplate to your pumpkin as shown.
Creating Your Wheel
Find a circle shape that is the same size or slightly smaller than your main black card. Trace it onto the larger cardstock piece (NOT the one with the half-circle punched out). Cut it out. This will become your wheel.
Find and mark the center of your circle.
One way to do this is to place the circle on a piece of paper and use a ruler to cut the paper to the same size as the circle. Then, measure each side and mark the halfway point. For instance, my paper was 4x4 inches. So, the center of each side was the 2 inch mark. I drew a line at each 2-inch mark, and where the lines intersected was the center of my paper.
I used my awl to create a hole in the center of my paper, then placed my circle on the paper, lining my circle edges with my paper edges, and flipped it over. Using a pencil, I marked through the hole I created onto my circle. You can also look up "How to find the center of a circle" if that is more helpful.
Create a hole in the center of your circle or
wheel. Then align the wheel in the bottom-center of your card (where you punched the half-circle). And mark through the center hole. Use the awl to punch it out.
Creating Your Window
This part is just a little tricky. It took me some trial and error. With the wheel aligned on the center bottom of your card, place the pumpkin over the top edge of the wheel so that your wheel shows through the window. (See photo above.) You'll want to align it carefully. The wheel should show through, but the edges of the wheel should not.
Now that you have your pumpkin and wheel aligned, carefully remove the wheel by sliding it away. Do
not move your pumpkin.
Use a pencil to trace inside your pumpkin bookplate onto your card.
Now, remove your pumpkin and use your craft knife to cut out where you marked with your pencil.
 |
| Back of card. |
Turn your card to the back (see above photo) and use your brass fastener to attach your wheel to the back of the card. Then flip it back to the front again.
 |
| Front of card. |
Your wheel should completely cover the window you cut out as shown above.
Adding Seasonal Words
Use glue to attach your cut-out "Seasons" Journal Words to the wheel, using the cut-out hole as a guide for placing the words. (See the above photo.)
When you've glued on a word, spin the wheel until the word disappears and attach another word. Repeat until the wheel is full of words. Try to space them evenly.
Note: Be sure to leave plenty of space between the words so no more than one shows up in the window at a time.
When you've finished applying your words to the wheel through the window, use a piece of tape to secure your brass fastener.
Attach Pumpkin
You might also want to secure the fasteners on your pumpkin book plate. Then glue your pumpkin to your card, lining up the window so the words show through and covering your brass fastener.
If your pumpkin isn't large enough to cover your fastener, consider using some
cheesecloth or decorative tissue paper underneath your pumpkin to hide the fastener. Just don't cover your window.
Print your Coffee Stained Book Page on cardstock and fold it in half as shown.
Use strips of mounting tape to attach your completed pumpkin card to the folded "Coffee Stained Book Page" card.
Align the pumpkin card with the bottom of the folding card as shown below.
If you want,
ink the edges of your card, and you're finished! Now you can use the punched out part at the bottom to move the spinning wheel and change the words in your window. See video below.
If you liked this tutorial, please share!
Thanks!
Stephanie from My Porch Prints
